Top printed circuit board assembly factory? Best Technology, establish on June 28, 2006, is a Hong Kong registered company whom focused on one-stop solution provider of FPC, Rigid-flex, MCPCB, FR4 PCB, Ceramic PCB, Special PCB such as Heavy Copper (up to 20 OZ), extra thin PCB (0.10, 0.15mm), and PCB assembly service. See additional info on thin core pcb. The layer on top of the copper foil is called the soldermask layer. This layer gives the PCB its green (or, at PCB & MCPCB, red) color. It is overlaid onto the copper layer to insulate the copper traces from accidental contact with other metal, solder, or conductive bits. This layer helps the user to solder to the correct places and prevent solder jumpers. In the example below, the green solder mask is applied to the majority of the PCB, covering up the small traces but leaving the silver rings and SMD pads exposed so they can be soldered to. Soldermask is most commonly green in color but nearly any color is possible. We use red for almost all the PCB & MCPCB boards, white for the IOIO board, and purple for the Best Technology boards.
A single sided flexible printed circuit (1 layer flex circuit) is a flex circuit with one layer of copper trace on one substrate, and with one layer Polyimide coverlay laminated to copper trace so that only one side copper will be exposed, so that it only allowing access to copper trace from one side, comparing to dual access flex circuit which allows access from both top and bottom side of flex circuit. As there’s only one layer of copper trace, so it also named as 1 layer flexible printed circuit, or 1 layer flexible circuit, or even 1 layer FPC, or 1L FPC. The multi layer flex circuit refer to a flex circuit with more than 2 layer circuit layers. Three or more flexible conductive layers with flexible insulating layers between each one, which are interconnected by way of metallized hole through the vias/holes and plating to form a conductive path between the different layers, and external are polyimide insulating layers. Quality Policy: PCB Quality is the core of products. All of engineer & vital department guys has more than five years expenrience in PCB industry, we follow up the default PCB standard, as well as with clients’ special request.
Heavy Copper Board does not have a set of definition per IPC. According to PCB industry, however, peopel generally use this name to identify a printed circuit board with copper conductors 3 oz/ft2 – 10 oz/ft2 in inner and/or outer layers. And Extreme heavy copper PCB refers to 20 oz/ft2 to 200 oz/ft2 printed circuit board. Heavy copper normally used for a various products but not limited to: high power distribution, heat dissipation, planar transformers, power convertors, and so on.
Today printed wiring (circuit) boards are used in virtually all but the simplest commercially produced electronic devices, and allow fully automated assembly processes that were not possible or practical in earlier era tag type circuit assembly processes. A PCB populated with electronic components is called a printed circuit assembly (PCA), printed circuit board assembly or PCB Assembly (PCBA). In informal use the term “PCB” is used both for bare and assembled boards, the context clarifying the meaning. The IPC preferred term for populated boards is CCA, circuit card assembly. This does not apply to backplanes; assembled backplanes are called backplane assemblies by the IPC.
According to different manufacturing method, current there’re three basic types for ceramic board: A) Thick Film Ceramic Board Thick Film Ceramic PCB: Using this technology, the thickness of conductor layer exceeds 10 micron, more thick than spurting technology. The conductor is silver or gold palladium, and was printed on ceramic substrate. More for Thick Film Ceramic PCB. B) DCB Ceramic Board DCB (Direct Copper Bonded) technology denotes a special process in which the copper foil and the core (Al2O3 or ALN), on one or both sides, are directly bonded under appropriate high temperature and pressure. Read more info at https://www.bstpcb.com/.
Metal Core PCB means the core (base) material for PCB is the metal, not the normal FR4/CEM1-3, etc. and currently the most common metal used for MCPCB manufacturer are Aluminum, Copper and steel alloy. Aluminum has good heat transferring and dissipation ability, but yet relatively cheaper; copper has even better performance but relatively more expensive, and steel can be divided into normal steel and stainless steel. It more rigid than both aluminum and copper, but thermal conductivity is lower than them too. People will choose their own base/core material according to their different application.